• General instructions - Safety instructions
  • Safety before all – General safety instructions
  • List of warning, mandatory and prohibition signs
  • Warning labels
  • Machine label
• Technical Specifications
• Handling and use

1.1. Features

• 1.1.1. Rotary engraving
• 1.1.2. Diamond scratching

1.2 Component names and functions

• 1.2.1. Front view
• 1.2.2. Rear view
• 1.2.3. Virtual keypad

2.1. Installation environment

2.2. Unpacking

• 2.2.1. Unpacking
• 2.2.2. Checking the contents of the box

2.3. Cable connections

• 2.3.1. Checking the supply voltage
• 2.3.2. Connecting the power cable
• 2.3.3. Connecting the X-300 to your computer or network

2.4. Installing the software

• 2.4.1. System requirements
• 2.4.2. Configuring the PC's ethernet port
• 2.4.3. Installing the Cyborg virtual pendent
• 2.4.4. Registering and starting the Cyborg pendent software
• 2.4.5. Installing the “Symmetry” engraving software
• 2.4.6. Using other third party software

3.1. Switching the power on and off

• 3.1.1. Switching the power on
• 3.1.2. Switching the power off

3.2. Securing the engraving material onto the engraving table

• 3.2.1. Using the standard included flat engraving table
• 3.2.2. Using the “MultiMat” sheet
• 3.2.3. Using the optional “quick lock vise”

3.3. Setting up a tool

• 3.3.1. How to use the optional cutter calibration stand
• 3.3.2. Installing an engraving tool
• 3.3.3. Installing a scoring tool
• 3.3.4. Installing a diamond scratch tool
• 3.3.5. How to remove a tool from the spindle

• 3.4.1. Engraving with floating nosecone
  • 3.4.1.1. Calibration of the nosecone and the optional cutter stand
  • 3.4.1.2. How to use the depth limiting nosecone
  • 3.4.1.3. How to use the spindel spring pressure
• 3.4.2. Engraving without floating nosecone
  • 3.4.2.1. Defining the plate surface
  • 3.4.2.2. How to enter the engraving depths in Symmetry
  • 3.4.2.3. Locking the spring pressure to engrave without nosecone

• 3.5.1. Materials rotation speed and feed
• 3.5.2. Two-way engraving metals
• 3.5.3. Adjusting feeds and speeds
• 3.5.4. Pause button
• 3.5.5. Cancelling the engraving job
• 3.5.6. Restarting the engraving job

• 3.6.1. Keypad overview
  • Introduction - General overview
  • Function keys
  • Settings screen
• 3.6.2. Setting and saving origin points

• 4.2.1. daily maintenance
• 4.2.2. weekly maintenance
• 4.2.3. monthly maintenance
• 4.2.4. annual maintenance

• 4.3.1. Replacing the spindle belt
• 4.3.2. Greasing the leadscrews
• 4.3.3. How to open the electronics drawer

5.1. The machine does not initialize

5.2. The spindle does not rotate

5.3. The engraving results are poor

5.4. No connection between machine and computer

• 7.1. Quick lock vise
• 7.2. Jigs for the quick lock vise
• 7.3. Output signal for switching on and off an external device at the beginning and the end of a job

A. Thesaurus: a glossary with specific terms about computerized engraving as being used in this manual.

B. G-code and M-code protocol for the Cyborg controller.