• General introduction - Safety Instructions
  • Safety before all – General safety instructions
  • List of warning, mandatory and prohibition signs
  • Warning labels
  • Machine label
• Technical Specifications
• Handling and use

1.1. Features

• 1.1.1. Rotary engraving
• 1.1.2. Diamond scratching

1.2 Component names and functions

• 1.2.1. Front view
• 1.2.2. Rear view
• 1.2.3. Virtual keypad

2.1. Installation environment

2.2. Unpacking

• 2.2.1. Unpacking
• 2.2.2. Checking the contents of the box

2.3. Cable connections

• 2.3.1. Checking the supply voltage
• 2.3.2. Connecting the power cable
• 2.3.3. Connecting the X-300 to your computer or network

• 2.4.1. System requirements
• 2.4.2. Configuring the PC's ethernet port
• 2.4.3. Installing the Cyborg virtual pendent
• 2.4.4. Registering and starting the Cyborg pendent software
• 2.4.5. Installing the “Symmetry” engraving software
• 2.4.6. Using other third party software

3.1. Switching the power on and off

• 3.1.1. Switching the power on
• 3.1.2. Switching the power off

3.2. Securing the engraving material onto the engraving table

• 3.2.1. Using the standard included flat engraving table
• 3.2.2. Using the “MultiMat” sheet
• 3.2.3. Using the optional “Auto centre vise”
• 3.2.4. Using the optional “Vacuum table”

3.3. Setting up a tool

• 3.3.1. How to use the cutter calibration stand
• 3.3.2. Installing an engraving tool
• 3.3.3. Installing a scoring tool
• 3.3.4. Installing a diamond scratch tool
• 3.3.5. How to remove a tool from the spindle

• 3.4.1. Calibrating and using the depth regulator nose
  • 3.4.1.1. Calibrating the depth regulator nose and the calibration stand
  • 3.4.1.2. Using the depth regulator nose
    • in combination with Auto Z control
    • without Auto Z control

• 3.4.2. Use of the spindle pressure spring
  • 3.4.3.1. Locking the pressure spring for engraving without depth regulator nose
  • 3.4.3.2. Auto plate surfacing with unlocked spring and engraving with locked spring
  • 3.4.3.3. Surface mapping with unlocked spring and engraving uneven surfaces with locked spring

• 3.5.1. Materials rotation speed and feed
• 3.5.2. Two-way engraving metals
• 3.5.3. Adjusting feeds and speeds
• 3.5.4. Pause button
• 3.5.5. Cancelling the engraving job
• 3.5.6. Restarting the engraving job

• 3.6.1. Keypad overview
  • Introduction - General overview
  • Function keys
  • Settings screen
• 3.6.2. Setting and saving origin points
• 3.6.3. Choosing Z modes

• 4.2.1. daily maintenance
• 4.2.2. weekly maintenance
• 4.2.3. monthly maintenance
• 4.2.4. annual maintenance

• 4.3.1. Replacing the spindle belt
• 4.3.2. Tensioning the timing belts
• 4.3.3. Removing the machine covers

5.1. The machine does not initialize

5.2. The spindle does not rotate

5.3. The engraving results are poor

5.4. No connection between machine and computer

• 7.1. Vacuum converter
• 7.2. Self centering vise
• 7.3. Jigs for the clamping vise
• 7.4. Output signal for switching on and off an external device at the beginning and the end of a job
• 7.5. Output signal for switching on and off an external device at every spindle up/down move

A. Thesaurus: a glossary with specific terms about all things computerized engraving as being used in this manual.

B. G-code and M-code protocol for the Cyborg controller.