| Both sides previous revision
Previous revision
Next revision
|
Previous revision
|
en:x300:choosing_z_modes [2022/09/22 13:17]
erik.ketele |
en:x300:choosing_z_modes [2023/05/17 10:05] (current)
|
| {{:en:x300:plate_surface_set_v2.png?150|}} | {{:en:x300:plate_surface_set_v2.png?150|}} |
| |
| {{:en:x300:set_surface.jpg?100|}}In this mode the system can use the “surface” proximity switch to determine the plate surface, both for working with or without nosecone. (See page….)\\ How to use the “set” option: When using the “set” option, make sure the black knurled spring pressure ring is screwed all the way up. Make sure you position the spindle above the area of your workpiece where you want to set surface. Do this before pushing the “set surface” key. Press the “set surface” key on the virtual pendent. You can now either push the Z down and the Z up keys to position the spindle to the level where you want Z to be 0, then press the Enter {{:en:x300:key_enter.png?30|}} key in the set surface window, or You can push the Z down {{:en:x300:key_dn.png?30|}} key till the spindle is still a little above the plate surface, then push the “Probe” {{:en:x300:probe.jpg?200|}} key in the “set surface” window. As long as you push the “probe” key the spindle will slowly move down and the Z=0 level will be set automatically. | {{:en:x300:set_surface.jpg?100|}}In this mode the system can use the “surface” proximity switch to determine the plate surface, both for **[[depth_regulator_nose_use|working with or without nosecone]]** How to use the “set” option: When using the “set” option, make sure the black knurled spring pressure ring is screwed all the way up. Make sure you position the spindle above the area of your workpiece where you want to set surface. Do this before pushing the “set surface” key. Press the “set surface” key on the virtual pendent. You can now either push the Z down and the Z up keys to position the spindle to the level where you want Z to be 0, then press the Enter {{:en:x300:key_enter.png?30|}} key in the set surface window, or You can push the Z down {{:en:x300:key_dn.png?30|}} key till the spindle is still a little above the plate surface, then push the “Probe” {{:en:x300:probe.jpg?200|}} key in the “set surface” window. As long as you push the “probe” key the spindle will slowly move down and the Z=0 level will be set automatically. |
| |
| === 2. Plate surface : auto === | === 2. Plate surface : auto === |
| - This system works for limited height differences and not for steep slopes. In any case, for safety reasons the Z safe lift has to be set higher than the height of the relief of the object to be mapped. | - This system works for limited height differences and not for steep slopes. In any case, for safety reasons the Z safe lift has to be set higher than the height of the relief of the object to be mapped. |
| - When using the “Map” option, make sure the black knurled spring pressure ring is screwed all the way up. | - When using the “Map” option, make sure the black knurled spring pressure ring is screwed all the way up. |
| - The images on the left show the default map window when the surface button is hit with the “map” option active. The second image shows a typical set of data to perform a surface scan. In this case a surface of 150mm x 150mm will be scanned with one scan point every 10 mm. the Z-down move speed to find the surface in this case is 15 mm/sec and after having found the surface at each scan point the spindle in this case moves up 10 mm before moving to the following scan point. | - The images hereunder show the default map window when the surface button is hit with the “map” option active. The second image shows a typical set of data to perform a surface scan. In this case a surface of 50mm x 50mm will be scanned with one scan point every 10 mm. the Z-down move speed to find the surface in this case is 30 mm/sec and after having found the surface at each scan point the spindle in this case moves up 5 mm before moving to the following scan point. |
| |
| | {{:en:x300:map_window_v2.png?250|}} {{:en:x300:map_window_ingevuld_v2.png?250|}} |
| | |
| | |
| | **Continue to [[daily|daily maintenance]].**\\ |
| **Continue to [[:en:x300:table_of_contents|the table of contents]].** | **Continue to [[:en:x300:table_of_contents|the table of contents]].** |
| |
| |
