en:x300:annual
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:x300:annual [2022/09/28 14:17] erik.ketele |
en:x300:annual [2023/10/20 12:24] (current) jan.vangelder |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Annual maintenance ===== | ===== Annual maintenance ===== | ||
| + | |||
| + | ---- | ||
| ==== important notices ==== | ==== important notices ==== | ||
| Line 20: | Line 22: | ||
| • Remove the screws, indicated on the image below (for the left cover).\\ | • Remove the screws, indicated on the image below (for the left cover).\\ | ||
| \\ | \\ | ||
| - | {{: | + | {{: |
| \\ | \\ | ||
| • Remove the screws, indicated on the image below (for the right cover)\\ | • Remove the screws, indicated on the image below (for the right cover)\\ | ||
| \\ | \\ | ||
| - | {{: | + | {{: |
| \\ | \\ | ||
| • Remove the 2 covers.\\ | • Remove the 2 covers.\\ | ||
| Line 30: | Line 32: | ||
| • Remove the 2 screws which are part of the hinges of the protective cover of the machine. (see the images below)\\ | • Remove the 2 screws which are part of the hinges of the protective cover of the machine. (see the images below)\\ | ||
| \\ | \\ | ||
| - | {{: | + | {{: |
| \\ | \\ | ||
| • Remove the screws, indicated on the images below (for the back cover).\\ | • Remove the screws, indicated on the images below (for the back cover).\\ | ||
| \\ | \\ | ||
| - | {{: | + | {{: |
| \\ | \\ | ||
| • Remove the top cover upwards and at the same time slightly to the rear.\\ | • Remove the top cover upwards and at the same time slightly to the rear.\\ | ||
| Line 46: | Line 48: | ||
| • If the timing belts are not really well tensioned anymore it is possible to retighten them.\\ | • If the timing belts are not really well tensioned anymore it is possible to retighten them.\\ | ||
| • To do so you will first have to unscrew hex screws A (2 pieces). Do not take them out, unscrew them about one turn.\\ | • To do so you will first have to unscrew hex screws A (2 pieces). Do not take them out, unscrew them about one turn.\\ | ||
| - | • After that you will need a torque wrench to apply the right tension to screw B. Release screw B a little bit, put the torque wrench in hex screw B, apply a tension of 1 Nm, and tightly rescrew both the A screws.\\ | + | • After that you will need a torque wrench to apply the right tension to screw B. Release screw B a little bit, put the torque wrench in hex screw B, apply a tension of **1,2 Nm**, and tightly rescrew both the A screws.\\ |
| \\ | \\ | ||
| **Note:** to have access to screw B you will first have to remove the front cover and the inner side covers. In the image hereabove you see the belt pulling mechanism of the left timing belt. The timing belt on the right hand side has an identical setup.\\ | **Note:** to have access to screw B you will first have to remove the front cover and the inner side covers. In the image hereabove you see the belt pulling mechanism of the left timing belt. The timing belt on the right hand side has an identical setup.\\ | ||
| Line 55: | Line 57: | ||
| • It is impossible to remove the cover without first loosening the spindle carriage. To do so, remove the 2 screws indicated with a yellow arrow (see image below)\\ | • It is impossible to remove the cover without first loosening the spindle carriage. To do so, remove the 2 screws indicated with a yellow arrow (see image below)\\ | ||
| • The procedure to tighten the X-axis belt is identical to the procedure to tighten the Y-axis belts.\\ | • The procedure to tighten the X-axis belt is identical to the procedure to tighten the Y-axis belts.\\ | ||
| + | Meer gedetailleerde info over het verewijderen van de afdekkap van de X-as vind je hier[[: | ||
| \\ | \\ | ||
| - | {{: | + | {{: |
| \\ | \\ | ||
| **Continue to [[: | **Continue to [[: | ||
en/x300/annual.1664367472.txt.gz · Last modified: 2022/09/28 14:17 by erik.ketele
